Z-Wave is a wireless communications protocol used primarily for home automation. It is a mesh network using low-energy radio waves to communicate from appliance to appliance, allowing for wireless control of residential appliances and other devices, such as lighting control, security systems, thermostats, windows, locks, swimming pools and garage door openers. Like other protocols and systems aimed at the home and office automation market, a Z-Wave automation system can be controlled from a wireless keyfob, a wall-mounted keypad or through smartphones, tablets or computers, with a Z-Wave gateway or central control device serving as both the hub controller and portal to the outside. It provides interoperability between home control systems of different manufacturers that are a part of its alliance. There are a growing number of interoperable Z-Wave products; over 1,700 in 2017, and over 2,400 by 2018.
Video Z-Wave
History
The Z-Wave protocol was developed by Zensys, a Danish company based in Copenhagen, in 2001. That year, Zensys introduced a consumer light-control system, which evolved into Z-Wave as a proprietary system on a chip (SoC) home automation protocol on an unlicensed frequency band in the 900 MHz range. Its 100 series chip set was released in 2003, and its 200 series was released in May 2005, with the ZW0201 chip offering a high performance at a low cost. Its 500 series chip, also known as Z-Wave Plus, was released in March 2013, with four times the memory, improved wireless range, and improved battery life. The technology began to catch on in North America around 2005, when five companies, including Danfoss, Ingersoll-Rand and Leviton Manufacturing, adopted Z-Wave. They formed the Z-Wave Alliance, whose objective is to promote the use of Z-Wave technology, with all products by companies in the alliance interoperable. In 2005, Bessemer Venture Partners led a $16 million third seed round for Zensys. In May 2006, Intel Capital announced that it was investing in Zensys, a few days after Intel joined the Z-Wave Alliance. In 2008, Zensys received investments from Panasonic, Cisco Systems, Palamon Capital Partners and Sunstone Capital.
Z-Wave was acquired by Sigma Designs in December 2008. Following the acquisition, Z-Wave's US headquarters in Fremont, California were merged with Sigma's headquarters in Milpitas, California. On January 23, 2018, Sigma announced it planned to sell its Z-Wave business to Silicon Labs for $240m, which was completed on April 18, 2018.
In 2005, six products on the market used Z-Wave technology. By 2012, as smart home technology was becoming increasingly popular, there were approximately 600 products using Z-Wave technology available in the US. By May 2017, over 1,700 products have been certified by the Z-Wave Alliance. As of April 18, 2018, there were over 2,400 interoperable Z-Wave products.
Maps Z-Wave
Interoperability
Z-Wave's interoperability layer ensures that devices can share information and allows all Z-Wave hardware and software to work together. Its wireless mesh networking technology enables any node to talk to adjacent nodes directly or indirectly, controlling any additional nodes. Nodes that are within range communicate directly with one another. If they aren't within range, they can link with another node that is within range of both to access and exchange information. In September 2016, certain parts of the Z-Wave technology were made publicly available, when Sigma Designs released a public version of Z-Wave's interoperability layer, with the software added to Z-Wave's open-source library. The open source availability allows software developers to integrate Z-Wave into devices with fewer restrictions. Z-Wave's S2 security, Z/IP for transporting Z-Wave signals over IP networks, and Z-Ware middleware are all open source as of 2016.
Standards and the Z-Wave Alliance
The Z-Wave Alliance was established in 2005 as a consortium of companies that make connected appliances controlled through apps on smartphones, tablets or computers using Z-Wave wireless mesh networking technology. The alliance is a formal association focussed on both the expansion of Z-Wave and the continued interoperability of any device that utilises Z-Wave.
In October, 2013, Sigma Designs and the Z-Wave Alliance announced a new protocol and interoperability certification program called Z-Wave Plus, based upon new features and higher interoperability standards bundled together and required for the 500 series system on a chip (SoC), and including some features that had been available since 2012 for the 300/400 series SoCs. In February 2014, the first product was certified by Z-Wave Plus. The alliance aims to create for the smart home a secure mesh network that works across different platforms.
Z-Wave is designed to achieve reliable communication and operation between devices and sensor-enabled objects from various manufacturers in the Z-Wave Alliance, which consists of over 450 members. Members of the alliance include Intermatic, Leviton, Techniku, Carrier, ADT Corporation, FAKRO, Ingersoll Rand, Jasco, LG Uplus, Nortek Security & Control, Sigma Designs, SmartThings, Honeywell, Bosch, Belkin, Zipato, August Home and Black & Decker.
Technical characteristics
Radio frequencies
Z-Wave is designed to provide reliable, low-latency transmission of small data packets at data rates up to 100kbit/s. The throughput is 40kbit/s (9.6kbit/s using old chips) and suitable for control and sensor applications, unlike Wi-Fi and other IEEE 802.11-based wireless LAN systems that are designed primarily for high data rates. Communication distance between two nodes is about 30 meters (40 meters with 500 series chip), and with message ability to hop up to four times between nodes, it gives enough coverage for most residential houses. Modulation is by Manchester channel encoding.
Z-Wave uses the Part 15 unlicensed industrial, scientific, and medical (ISM) band. It operates at 868.42 MHz in Europe, at 908.42 MHz in the North America and uses other frequencies in other countries depending on their regulations. This band competes with some cordless telephones and other consumer electronics devices, but avoids interference with Wi-Fi, Bluetooth and other systems that operate on the crowded 2.4 GHz band. The lower layers, MAC and PHY, are described by ITU-T G.9959 and fully backwards compatible. In 2012, the International Telecomunications Union (ITU) included the Z-Wave PHY and MAC layers as an option in its G.9959 standard for wireless devices under 1 GHz. Data rates include 9600 bps and 40 kbps, with output power at 1 mW or 0 dBm. The Z-Wave transceiver chips are supplied by Sigma Designs and Mitsumi.
Table of used frequencies in various parts of the world as of January 2017:
Network setup, topology and routing
Z-Wave uses a source-routed mesh network architecture. Mesh networks are also known as wireless ad hoc networks. In such networks, devices use the wireless channel to send control messages which are then relayed by neighboring devices in a wave-like fashion. The source device wanting to transmit is therefore known as the initiator. Hence, the name source-initiated mesh ad hoc routing. There were several source-initiated mesh routing protocols proposed in the period early 1990s. The earlier ones were Associativity-Based Routing (ABR) and Dynamic Source Routing (DSR)..
Devices can communicate to one another by using intermediate nodes to actively route around and circumvent household obstacles or radio dead spots that might occur in the multipath environment of a house. A message from node A to node C can be successfully delivered even if the two nodes are not within range, providing that a third node B can communicate with nodes A and C. If the preferred route is unavailable, the message originator will attempt other routes until a path is found to the C node. Therefore, a Z-Wave network can span much farther than the radio range of a single unit; however, with several of these hops a slight delay may be introduced between the control command and the desired result.
The simplest network is a single controllable device and a primary controller. Additional devices can be added at any time, as can secondary controllers, including traditional hand-held controllers, key-fob controllers, wall-switch controllers and PC applications designed for management and control of a Z-Wave network. A Z-Wave network can consist of up to 232 devices, with the option of bridging networks if more devices are required.
A device must be "included" to the Z-Wave network before it can be controlled via Z-Wave. This process (also known as "pairing" and "adding") is usually achieved by pressing a sequence of buttons on the controller and on the device being added to the network. This sequence only needs to be performed once, after which the device is always recognized by the controller. Devices can be removed from the Z-Wave network by a similar process. The controller learns the signal strength between the devices during the inclusion process, thus the architecture expects the devices to be in their intended final location before they are added to the system. Typically, the controller has a small internal battery backup, allowing it to be unplugged temporarily and taken to the location of a new device for pairing. The controller is then returned to its normal location and reconnected.
Each Z-Wave network is identified by a Network ID, and each device is further identified by a Node ID. The Network ID (also called Home ID) is the common identification of all nodes belonging to one logical Z-Wave network. The Network ID has a length of 4 bytes (32 bits) and is assigned to each device, by the primary controller, when the device is "included" into the Network. Nodes with different Network IDs cannot communicate with each other. The Node ID is the address of a single node in the network. The Node ID has a length of 1 byte (8 bits) and must be unique in its network.
The Z-Wave chip is optimized for battery-powered devices, and most of the time remains in a power saving mode to consume less energy, waking up only to perform its function. With Z-Wave mesh networks, each device in the house bounces wireless signals around the house, which results in low power consumption, allowing devices work for years without needing to replace batteries. For Z-Wave units to be able to route unsolicited messages, they cannot be in sleep mode. Therefore, battery-operated devices are not designed as repeater units. Mobile devices, such as remote controls, are also excluded since Z-Wave assumes that all repeater capable devices in the network remain in their original detected position.
Security
Z-Wave is based on a proprietary design, with Sigma Designs as its primary chip vendor. In 2014, Mitsumi became a licensed second source for Z-Wave 500 series chips. Although there have been a number of academic and practical security researches on home automation systems based on Zigbee and X10 protocols, research is still in its infancy to analyze the Z-Wave protocol stack layers, requiring the design of a radio packet capture device and related software to intercept Z-Wave communications. An early vulnerability was uncovered in AES-encrypted Z-Wave door locks that could be remotely exploited to unlock doors without the knowledge of the encryption keys, and due to the changed keys, subsequent network messages, as in "door is open", would be ignored by the established controller of the network. The vulnerability was not due to a flaw in the Z-Wave protocol specification but was an implementation error by the door lock manufacturer.
On November 17, 2016, the Z-Wave Alliance announced stronger security standards for devices receiving Z-Wave Certification as of April 2, 2017. Known as Security 2 (or S2), it provides advanced security for smart home devices, gateways and hubs. It shores up encryption standards for transmissions between nodes, and mandates new pairing procedures for each device, with unique PIN or QR codes on each device. The new layer of authentication is intended to prevent hackers from taking control of unsecured or poorly secured devices. According to the Z-Wave Alliance, the new security standard is the most advanced security available on the market for smart home devices and controllers, gateways and hubs.
Hardware
The chip for Z-Wave nodes is the ZW0500, built around an Intel MCS-51 microcontroller with an internal system clock of 32 MHz. The RF part of the chip contains an GisFSK transceiver for a software selectable frequency. With a power supply of 2.2-3.6 volts, it consumes 23mA in transmit mode. Its features include AES-128 encryption, a 100kbps wireless channel, concurrent listening on multiple channels, and USB VCP support.
Comparison to other protocols
For smart-home wireless networking, there are numerous technologies competing to become the standard of choice. Wi-Fi consumes a lot of power, and Bluetooth is limited in signal range and number of devices. Other network standards competing with Z-Wave include Insteon, Thread and ZigBee. Of the three, Z-Wave has the longest open-air operating range at 300 feet (outdoor) and 80+ feet (indoor). Insteon has the largest number of maximum devices capability at 17.7 million (to ZigBee's 65,000 and Z-Wave's 232). Thread has the fastest data transmission rate at 250 kbps. Z-Wave has better interoperability than ZigBee, but ZigBee has a faster data transmission rate. Thread operates on the busy Wi-Fi standard frequency of 2.4 GHz, while Z-Wave operates at 908 MHz in the US, which has reduced noise and a greater coverage area. ZigBee operates on both 915 MHz and 2.4 GHz frequencies. All three are mesh networks. The Z-Wave MAC/PHY is globally standardized by the International Telecommunications Union as ITU 9959 radio, and the Z-Wave Interoperability, Security (S2), Middleware and Z-Wave over IP specifications were all released into the public domain in 2016, making Z-Wave highly accessible to Internet of Things developers.
See also
- Wi-Fi
- Bluetooth
- Zigbee
- Thread (network protocol)
- Belkin Wemo
- Insteon
References
External links
- Official website
Source of article : Wikipedia
0 Comments